System Services FrameworkInstallation and UseP/N: 6806800S58ENovember 2014
System Services Framework Installation and Use (6806800S58E)10List of Figures
System Services Framework Installation and Use (6806800S58E)11About this ManualOverview of ContentsThis manual provides information on installation, c
System Services Framework Installation and Use (6806800S58E)About this Manual12About this ManualConventionsThe table below describes the conventions u
About this ManualSystem Services Framework Installation and Use (6806800S58E)13Summary of ChangesIndicates a hazardous situation which, if not avoided
System Services Framework Installation and Use (6806800S58E)About this Manual14About this Manual
Chapter 1System Services Framework Installation and Use (6806800S58E)15Introduction1.1 OverviewSystem Services Framework (SSF) is a management and con
IntroductionSystem Services Framework Installation and Use (6806800S58E)161.2 Block DiagramThe following figure illustrates various components of SSF.
IntroductionSystem Services Framework Installation and Use (6806800S58E)17Using these interfaces, you can: Edit SSF configuration View general syste
IntroductionSystem Services Framework Installation and Use (6806800S58E)18 Storing of configuration in a database running on persistent memory or a m
IntroductionSystem Services Framework Installation and Use (6806800S58E)19The command line interface of SSF has the following capabilities: CLI acces
© Copyright 2014 Artesyn Embedded Technologies, Inc.All rights reserved.TrademarksArtesyn Embedded Technologies, Artesyn and the Artesyn Embedded Tec
IntroductionSystem Services Framework Installation and Use (6806800S58E)20The XML agent handles the XML interface of SSF. It passes management request
Chapter 2System Services Framework Installation and Use (6806800S58E)21Prerequisites2.1 Hardware RequirementsSSF can be installed on various Artesyn b
PrerequisitesSystem Services Framework Installation and Use (6806800S58E)222.1.2 Hardware Requirements for External SetupSSF can also run on a PC to m
PrerequisitesSystem Services Framework Installation and Use (6806800S58E)232.2.2 Software Requirements for Installation of SSF Core on External PCThis
PrerequisitesSystem Services Framework Installation and Use (6806800S58E)242.3 Shelf ID ConfigurationSSF supports shelf IDs 1 to255. You can configure
Chapter 3System Services Framework Installation and Use (6806800S58E)25SSF Installation3.1 OverviewPlease refer Chapter 2, Prerequisites, on page 21 f
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)26ssf_csim_rel-<Blade>-<version>.x86_64.rpmProvides CSIM binar
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)273.2 Installing SSF with System Manager on PrAMC-7311This section describ
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)283.2.1 Installing Dependent Packages on PrAMC-7311 based System ManagerIn
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)29$ hpmcmd -c motshelftypeFollow the below step to update the shelf type:
ContentsSystem Services Framework Installation and Use (6806800S58E)3About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)30rpm -ivh libgetshelfon<shelftype>-1.0-1.i686.rpm After successful
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)31Figure 3-1 Files in main Folder
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)323.2.4 Installing Blade SSF Core on PrAMC-7311If user wants to use System
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)33In the RPM command above, replace the strings <Blade>, <version
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)343.2.5 Installing SSF Application AgentTo manage applications (ViewCheck
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)35In the RPM command above, the string <Application Agent> should be
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)36After you start the SSF core, you can stop, restart, and check the statu
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)37To start the Blade SSF core: 1. Set the IP address of SSF in the ssfApi.
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)38system for system management. List of all dependent packages in this set
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)39 CentOS release 6.4 on 32-bit platform (http://ftpmirror.your.org/pub/c
System Services Framework Installation and Use (6806800S58E)Contents4ContentsContents3.3.1.1 Installing CentOS on Connected PC . . . . . . . . . . .
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)403.3.1.1 Installing CentOS on Connected PCThis section describes installi
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)41Note: For any of the CentOS6.3 or CentOS6.4 installation, make sure tha
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)423.3.1.2 Installing Red Hat Linux on Connected PCThis section describes i
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)433.3.2 Installing SSFThis section describes installing SSF on external PC
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)446. The RunSSFOn<Linux OS version>PC.sh script checks the existing
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)459. Enter 1 to select the Platform Preparation option. It installs all th
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)46The following figure shows completion of platform preparation along with
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)473.3.3 Installing Blade SSF CoreBlade SSF core is an agents to SSF on res
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)483.3.4 Installing SSF Application AgentTo manage applications (ViewCheck
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)49In the RPM command above, the string <Application Agent> should be
ContentsSystem Services Framework Installation and Use (6806800S58E)5A.6 Installing SSF on PrAMC-7311 using Ramdisk Installation . . . . . . . . .
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)50When a new package SSF-REL_<new ssf release version>_EL5_R1.1.tar.
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)51To install the new package refer Chapter 3, Installing Linux on connecte
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)523.3.6 Configuring System Network1. IP Address assignmentBy default, SSF
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)53The following figure shows the changed VLAN configuration:Note: Make su
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)54Note: Make sure the ShelfId is updated as per section Chapter 2, Shelf
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)55To start the Blade SSF core:1. Set the IP address of SSF host in the ssf
SSF InstallationSystem Services Framework Installation and Use (6806800S58E)56
Chapter 4System Services Framework Installation and Use (6806800S58E)57SSF Configuration4.1 OverviewThis section provides the details of different con
SSF ConfigurationSystem Services Framework Installation and Use (6806800S58E)58ssf.ini CLI ConfigFile ScriptsDirThis file is used to edit the CLI co
SSF ConfigurationSystem Services Framework Installation and Use (6806800S58E)594.3 Blade SSF Core ConfigurationBlade SSF core consists of SSF-BCSIM (s
System Services Framework Installation and Use (6806800S58E)Contents6ContentsContents
SSF ConfigurationSystem Services Framework Installation and Use (6806800S58E)60Use the following the conventions to add a service: Service name shoul
SSF ConfigurationSystem Services Framework Installation and Use (6806800S58E)61User can monitor different events using the configuration parameters as
SSF ConfigurationSystem Services Framework Installation and Use (6806800S58E)624.3.3 Firmware Upgrade Facility ConfigurationThe Firmware Upgrade Facil
SSF ConfigurationSystem Services Framework Installation and Use (6806800S58E)63} - Indicates the end of the FUF configuration for the %DEVICE.: - Afte
SSF ConfigurationSystem Services Framework Installation and Use (6806800S58E)64New Device Firmware Upgrade Support:To add firmware upgrade support to
SSF ConfigurationSystem Services Framework Installation and Use (6806800S58E)654.4 SSF Application Agent ConfigurationSSF application agent consists o
SSF ConfigurationSystem Services Framework Installation and Use (6806800S58E)66Follow the procedure to configure SSF application agent:1. Configure th
SSF ConfigurationSystem Services Framework Installation and Use (6806800S58E)675. As there is no dhclient present in the BBS of packet processor core,
SSF ConfigurationSystem Services Framework Installation and Use (6806800S58E)68
Chapter 5System Services Framework Installation and Use (6806800S58E)69Accessing SSF5.1 OverviewAfter installing and configuring SSF, you can access i
List of TablesSystem Services Framework Installation and Use (6806800S58E)7Table 1-1 Command Line Editing Features . . . . . . . . . . . . . . . . .
Accessing SSFSystem Services Framework Installation and Use (6806800S58E)702. In the Login dialog box, type your username and password.3. Click Login
Accessing SSFSystem Services Framework Installation and Use (6806800S58E)71Username: AdminPassword:Access granted>enable#configure terminalSSF(conf
Accessing SSFSystem Services Framework Installation and Use (6806800S58E)724. Keep the secure ssh connection open in y.y.y.y and open another shell in
Appendix ASystem Services Framework Installation and Use (6806800S58E)73A Additional InformationA.1 Example for Configuring Shelf IDFollowing are the
Additional InformationSystem Services Framework Installation and Use (6806800S58E)743. Update the 'DomainTag' field in the file with appropr
Additional InformationSystem Services Framework Installation and Use (6806800S58E)755. Reset the administrator password using the following command:SS
Additional InformationSystem Services Framework Installation and Use (6806800S58E)76Configuring multiple shelves in HPI-B client's configuration
Additional InformationSystem Services Framework Installation and Use (6806800S58E)77# mkdir tmp# cd tmp# gzip -dc ../initramfs.cpio.gz | cpio -i -d -H
Additional InformationSystem Services Framework Installation and Use (6806800S58E)78rpm -ivh /opt/bladeservices/rpms/ssf_gui_console_rel-7311-1.1.5.x8
Appendix BSystem Services Framework Installation and Use (6806800S58E)79B Related DocumentationB.1 Artesyn Embedded Technologies - Embedded Computing
System Services Framework Installation and Use (6806800S58E)8List of Tables
Related DocumentationSystem Services Framework Installation and Use (6806800S58E)80SRstackware Intelligent Network Software OSPF Command Reference 680
Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Technologies, Inc.All ot
List of FiguresSystem Services Framework Installation and Use (6806800S58E)9Figure 1-1 SSF Block Diagram . . . . . . . . . . . . . . . . . . . . . .
Kommentare zu diesen Handbüchern